How to put wooden slats on the terrace?
Here’s how to install a screw-in wood plank platform in 6 steps:
- Install the joists.
- Cut the first boards.
- Create a drilling template.
- Secure the first line.
- Install the following programs.
- Place the finished board on the side strip.
How much space should be left between decking boards?
Expect terrace movements: depending on the seasons and the humidity, the boards will expand or draw your wooden terrace. To avoid any inconvenience, allow a spacing between 3 and 12 mm maximum. Similarly, two blades end to end should be spaced about 5mm apart.
How to install deck boards without joists?
As usual, pre-drill bridge programs. Put them in final position. Mark the holes in the concrete substrate with a 4mm drill bit. Remove the boards, finish the holes at 6mm.
What is the thickness of the joist?
The joists can be of variable thickness (28.45, 60 mm). On the other hand, the width must always be greater than 50 mm, according to DTU 51-4, but a width of 70 mm is ideal to be able to connect 2 platform boards and fix the stainless steel screws correctly.
How to install composite deck joists?
The joists are installed along the length of the platform, so that the boards are wide. Place a maximum spacing of 35 cm on the joists. Place blocks under the joists and space them every 40 cm maximum. Each end of the sweater will rest on a stud.
What is the thickness of the joist for the wooden planks?
The beams are made of reduced wood compared to the beams, they are laid in a regular way: every 40 to 50 cm on boards 21 mm thick, which makes it possible to avoid bending of these and good stability long-term wood platforms.
How to repair a pergola on a wooden terrace?
How to repair a pergola?
- find out where you want to attach the pergola;
- dig holes about fifty centimeters deep;
- the bottom line with sand and gravel;
- place the legs of the structure;
- fill the holes with concrete.
A lire également
How to install deck boards on concrete?
They should then be placed on PVC corners, placed approximately every 50 cm. Arrange the joists along the edge of the platform, so that the joints are well glued. Fix the joists to the floor using floor anchors, having previously drilled the guest and the concrete.
How do you fasten a board to concrete?
Using nails The cut nail has a square, tapered shape with a square tip. These nails are driven through a board and into the concrete below, similar to driving a wood board nail into a wooden floor.
How to fix a threaded rod in concrete?
Chemical anchoring is a process of fixing a threaded rod into concrete using a very strong two-component chemical resin. By injecting it directly into the bottom of the hole, it will plug the hole while holding the screw. It will then harden and be as strong as concrete.
How to set Tirefond in concrete?
After drilling the hole, the flush anchor is assembled with the concrete, using a mallet, to push it. Insert each lag screw or dowel into the holes at the bottom of the post before proceeding with the screw, which will be fully done, and which will of course be straight.
How to embed a threaded rod in concrete?
Drill a hole with a hammer drill, using a concrete drill bit corresponding to the size of the chemical anchor to be inserted. Unpack the chemical sealing equipment. Screw the plastic cannula onto the end of the cartridge and place the assembly in the gun. Insert the chemical anchor into the hole.
How to attach joists to concrete baseboards?
The joists must always be isolated from the ground with PVC studs, foundation screws. If you’re building concrete plinths, you should place the joists on top of them, anchor them with screws and dowels, and ideally insulate the angel from the concrete plinth with a plastic wedge.
How to arrange decking boards over tiles?
To apply it, you must first make a pilot hole in the guest, then drill the slab, put the dowel in it and finally hit it. To install the apron, you have the choice between invisible fasteners or visible fasteners.
What is the importance of joists?
In the case of an installation on a slab, the joists are installed in the direction of the width, that is to say on the small side perpendicular to the ground. In the case of installation on a plinth, it is the reverse, that is to say the longest side vertically, to increase the mechanical resistance.
How to position the beam?
3 types of laying: The first is the traditional way: the beams are aligned every 45cm. This is the classic way to fix its structure. The classic beam is the simplest to implement! The second is the double jumper: the joist is doubled at each component of the boards.
How to install joists on a wooden deck?
Joists can be secured to the floor with impact anchors. The size of the ankles varies according to the height of the ankle. The rule is to use a 2.5 x thief height anchor to attach. The pegs must be spaced every 80 cm maximum.
What is the distance between 2 joists?
The spacing between the joists must be 50 cm during installation. This center length can be reduced to less than 40 cm for thinner joists and for a tighter platform.
How to extend the joist?
The joists are oriented perpendicular to the installation direction of the boards. If you have to stretch them, their territory should never be touched. On the contrary, an expansion space of 10 mm should be reserved. Secure the joists to the pedestals or the concrete slab.
How to put joists?
Note that the joists must be autoclaved. Put down your gears without repairing them. Trace, with a chalk line, or a free ruler and a pencil, the demarcation line of the platform on the joists. Using a circular saw, cut the joists along the track.
How to connect 2 joists?
Joist connectors allow you to attach two jaws, three screws to one side, using the included screws. For installation on pedestals, the joists (or rafters) must be bolted and screwed to the foot if possible for better rigidity.
How to arrange decking boards?
For softwood boards, you can fix the screws directly. First, tighten the screws only a few millimeters because there is a risk of completely tightening the cord. The body of the screw must be aligned with the bead in contact.
How to install the first decking board?
Start by placing the first plank at one end, leaving a space of at least 10 mm for the various emerging structures (walls, low walls, posts, etc.). Then secure this card with two screws on each jumper.
How to fix the boards on the joists?
Screw without splitting the wood
- Select a screw point at least 2cm from the ends of your blade.
- Pre-drill the hole a little thinner than your screw (unless using a self-drilling screw or installing exotic wood)
Which beam bolts?
You have the choice between A2 or A4 quality stainless steel screws. As for the size, it all depends on the species and the thickness of the wood: 5 × 50 mm for exotic woods, from 19 to 21 mm thick and 5 × 60 mm for softwoods, thickness between 22 and 28 mm.
How to glue wooden planks together?
Laying wooden slabs on soft ground: clay or grass Find out where the studs are. Dig 30 x 30 cm holes at each stud location, 3 to 4 cm deep. Throw in a thin layer of washed sand to perfectly balance the level.
How to repair composite panels?
Number of anchors 4 to hit for each Océwood® composite guest, spaced approximately 90 cm apart.
- Arrange the joists along the edge of the platform observing the centers of extension (15mm) between the joists…
- … …
- Drill through the joist and the concrete.
- Secure the joists to the floor using impact anchors.
Wooden boards for the terrace: how to obtain a reference terrace?
Wooden deck boards are references in France to enhance a garden that needs it. There are many wooden slats to prepare and equip your terrace. In France, garden terraces are often made of wood to give volume, diversify the arrangements between the garden, gravel or even grass. The work detailed above is technical and requires specialists.
However, before carrying out its construction, it is necessary to choose wooden blades on average between 2 meters 40 and 3 meters in length. Then about ten centimeters wide.
The installation of a wooden terrace requires reflection. Indeed, before starting the work, the choice of blades allows you to start decisive work to modify your garden or yard. In France, there are dozens of type of wooden blade for your garden terrace.
In detail, the French who hesitate on their wooden blade, there are solutions between light wood, a slightly dark shade or a mix between the two.
For the French who like light wood, the green spruce decking boards provide beautiful light to illuminate the garden.
Wooden decks with a slightly more neutral tone, pine deck boards are wonderful for bringing softness to your garden and letting the elements coexist together.
Conversely, for the French who love wooden terraces full of contrast, Elbi wooden joists bring another atmosphere to a garden that already has many elements. The Elbi wooden decking features boards with a worn but elegant material with a Finnish style.
Leave a Reply